Fantom-S and Fantom-X

Sustain pedal cords

Sustain pedal cords

22 Nov 2006, 21:10
I bought a GPP-3 by CME to go along with my X8.

Link to their site, just in case: www.cme-pro.com.

Trouble is, I can get the 2 pedals on the left (control pedals) to behave properly, but the right pedal (sustain) won't work. Sometimes the sustain will simply continue once powered on and no amount of pedal pushing stops it, and most of the time nothing happens. The GPP-3 uses TR cables for the 2 on the left and a TRS for the sustain; what are the Fantom X8's inputs for control and hold? Perhaps the cable setup just disagrees?

Any help would be fantastic, as I like this pedal but am getting aggravated trying to make it work :(
Aida ~
Fantom X8

Re: Sustain pedal cords

26 Nov 2006, 21:29
/bump because I still need an answer, please ^^
Aida ~
Fantom X8

Re: Sustain pedal cords

26 Nov 2006, 22:23
You may need to go into your controller settings and change the polarity for sustain pedal. If it's showing "-", change it to "+". I don't know why each manufacturer decides on having a different polarity for sustain. My Korg instruments do not like my Yamaha pedal and I end up with what you describe if I don't change the settings. Hope that helps.

EJ2 - Double EJ Projects: 9 Fully Karmafied Combi Collections for the Korg Karma or KarmaTriton http://2ej2.tripod.com/
Cheers,
Eric
EJ2 Sounds for You Synth/Workstation
http://www.freewebs.com/ejs2/

Re: Sustain pedal cords

26 Nov 2006, 22:40
I've changed the polarity settings through the Fantom, does it make a difference to change it through the hardware? (I'll try this again later tonight and see if it works, but I think I've tried this already...)
Aida ~
Fantom X8

Re: Sustain pedal cords

27 Nov 2006, 21:47
Man let me know if you get that to work, that pedal looks sweet. Certainly more elegant than my two DP-8's zip-tied to a piece of plastic.

Still need an answer, please...

12 Dec 2006, 17:14
...to my initial question:

The GPP-3 pedal (full set of 3 piano pedals) uses TR cables for the 2 on the left and a TRS for the sustain on the right; what are the Fantom X8's inputs for control and hold?

Aida ~
Fantom X8
Aida ~
Fantom X8

PLEASE PLEASE

15 Dec 2006, 19:37
Someone please answer my question. It doesn't seem to difficult, just need to know what type of inputs the CONTROL and SUSTAIN are, TR or TRS :(

Aida ~
Fantom X8
Aida ~
Fantom X8

GPP 3 sustain

26 Dec 2006, 23:23
Aida -

I think sustain port of x6-7-8 accepts either/or (I have a TRS yamaha sustain pedal in mine). As far as the GPP 3, make sure you have a power supply (aka wall wart) plugged in (NOT included with the pedal). Also, you might want to start at ground zero and reset the pedal to make sure the right CC#'s are going into the fantom. To do this, hold all three pedals simultaneously while powering on the pedal, and wait for the lights on the pedal unit to stop blinking. Pedal 1 and 2 take TS cords, pedal 3 takes a TRS. You could also use the MIDI out of the pedal to the fantom. The CC# for sustain is 64, which would be the value of pedal 3 once you've performed the reset. Good luck.
www.davecremonese.com

← Back to Fantom-S and Fantom-X