Fantom-S and Fantom-X

HELP! PLEASE!!!

HELP! PLEASE!!!

1 Sep 2005, 21:22
This situation is about to drive me absolutely ape-s**t. I have only had my x7 for about 2 months and for some reason, all of a sudden when I am playing in the Mixer there will be periods of 5-10 seconds where I will lose sound from my keyboard (I can still hear faint noise) and then it will come back. The strange thing is that if I switch to patch, layer/split, or piano mode while this is taking place it will function perfectly fine. This problem also occurs at times when I playback performances in the Mixer. I have tried to change the power source but that hasn't helped so I really don't know what else to do. Another strange thing is that for some reason the level slider on track 3 will slide up and down on its own and I am not even recording or playing on that track. Now I understand that there could be some problems with complex pieces but that is not what I am dealing with. Can anyone with any knowledge of thiis problem PLEASE help me??? I ahve been searching previous posts for the last couple of days but haven't seen anything. This is becoming very discouraging and is starting to blow my Fantom high.

Re: HELP! PLEASE!!!

1 Sep 2005, 23:11
Tracks are not specitic to channels. Any trck can have volume controller messages for any channel or all channels. Go into microscope mode and step through al of the tracks. Watch for controller #7 on channels that you are having the problem on.
Korg Oasys
Roland MV-8800

Re: HELP! PLEASE!!!

2 Sep 2005, 00:51
I am not sure what "microscope mode" is. Do you mean micro edit? I don't think it has anything to do with the tracks because it also happens when there is nothing recorded. I don't know if it's a settings issue or a technical issue. I lookd in the manual for microscope mode but I could not find it. Thank for the response though.

Re: HELP! PLEASE!!!

2 Sep 2005, 11:02
Cj

The thing that imediately comes to my mind is that probably one of the REALTIME CONTROL Knobs is malfunctioning. So it randomly sends volume or expression messages do the part you're playing. You can sort this out if you take a closer look at the MIXER.
Try to find out if the part is always the same and if the values change if you move the cursor to other parameter or if you change the assigned function of the Knobs (with the switch at its right side).


o - ...just could not afford the 8
(
\_/
hear what I've done with the 7

Re: HELP! PLEASE!!!

2 Sep 2005, 12:35
Cj,

'Microscope mode' is Micro Edit. MIDIguru may be on the right track here in terms of isolating this problem.

Try this: Load an existing Song that has exhibited these problems or record some stuff.
Instead of using Micro Edit to selectively erase Sysex messages (Sysex messages would cause the slider to move as you described) or CC messages that could be causing this, you can go into Song Edit>Track Edit>Erase.

Select Track:ALL, Measure 1 for ALL.
In the STATUS field, use the dec/inc buttons to scroll through and select 'Control Change'. 'Exec' and erase all of these. Then do the same operation but select 'System Exclusive' in the STATUS field.

You will now have a clean slate. Play back the Song or Tracks that you recorded and see if the problems persist. If they are gone, you may indeed have the problem that fixthemix is talking about.

To further help isolation, re-record some Tracks after clearing out the CC and Sysex messages and see if there are new CC and Sysex messages embedded that shoudn't be there. If there are, you could very well indeed have malfunctioning hardware.

Please try some of the suggested procedures and let us know what you get. If there is any further clarification you can give, it would help, just in case we are getting off-track.

Bassman
Bassman

Re: HELP! PLEASE!!!

6 Sep 2005, 22:03
im not positive but i think i seen a patch update on the roland us site that corrects this vary problem. its a 2.0 to 2.11 update or somthing like that. so dont sweat it its not the gear its the software.
Merlin Studios Music
Download my tracks

Re: HELP! PLEASE!!!

17 Sep 2006, 01:14
I can confirm that the v2.10 update does NOT solve the drifting realtime control knob issue. I just finished installing the update... and the problem continues.

I haven't seen anything that suggests I'll be able to resolve this without returning it to Roland... which really does suck.

~Gary

← Back to Fantom-S and Fantom-X