FA-06 / FA-07 / FA-08

Fa 06 and Korg volca, how to block sending events (solved)

Fa 06 and Korg volca, how to block sending events (solved)

23 Jan 2016, 06:20
Hi,
I have roland fa 06 connected to Korg volca sample. When I hit play song Fa sends midi clock sync to Volca to trig patterns, but unfortunately it also plays single notes on korg volca (channels 1-10 , as each sample has own midi channel and I have some midi events on these channels to play internal Fa06 patches)
How to send midi clock sync from fa06 to volca, but block sending any other events (especially notes) to volca sample?


Cheers,
Piotr
Last edited by piotr979 on 25 Jan 2016, 13:17, edited 1 time in total.

Re: Fa 06 and Korg volca, how to block sending events to Vol

23 Jan 2016, 15:12
Hello Piotr,

unfortunately, due to a major bug in FA, this would be not possible without tricks.
Normally, this is be done by setting the propriate track in the sequencer mode to EXT or INT.
So setting a track to INT would not send any midi to external devices and vice versa.
But this won't work.

Only way I see is to completely split yout midi channels. This means NOT using i.e. channels 1-10 in the FA because they are reseved fo the Korg.
If you have some tracks to play FA internal, then use only midi channels 11-16 for those tracks.
Midi channels can be changed in the Studio Set main page.

It is far limiting in a way but may be usefull workaround.

cheers, Benny Seven

Re: Fa 06 and Korg volca, how to block sending events to Vol

24 Jan 2016, 12:00
Thats really bad, it limits Fa significantly, I had Alesis fusion before and it was very bugged instrument, therefore i bought synth from roland, as i thought its more reliable instrument, sooo wrong :(

Re: Fa 06 and Korg volca, how to block sending events to Vol

25 Jan 2016, 13:12
I was looking for that settings (EXT/INT) and finally found it (manual page 63). Suprisingly changing track settings to internal helped! Now Roland plays notes using internal engine and doesn't send midi messages to my Volca except midi clock sync!
I'ts weird as I found more info on rolandclan forum that it was reported as a bug.

Re: Fa 06 and Korg volca, how to block sending events (solve

25 Jan 2016, 16:14
Yes, it is a bug the other way round. If you want only to send to EXT and don't want to use internal tones, it always send EXT and INT (like BOTH).

Re: Fa 06 and Korg volca, how to block sending events (solve

2 Feb 2016, 11:30
There is an easy cure for the EXT/INT setting problems...

For the sequencer to play internal sounds only......... set up the track to 'INT' in track settings

For the sequencer to play external sounds only........... leave the track settings as default 'INT and EXT' and mute the track

Re: Fa 06 and Korg volca, how to block sending events (solve

2 Feb 2016, 14:03
Yes, this is a good workaround. But always remember that muted tracks will use and consume internal voices, even they are muted (not routed to output bus).

If you have external tracks with many note events, the muted internal tracks may use many voices out of the FA's 128 voices.
Maybe a "voice reserve = 1" on that part/track will prevent from side effects.

Better way is tu use a bogus tone (zero voice construction).

Re: Fa 06 and Korg volca, how to block sending events (solve

3 Feb 2016, 11:25
But always remember that muted tracks will use and consume internal voices, even they are muted (not routed to output bus).
I thought that most modern synths only use up the notes/voices/polyphony resource out of what is being played at any time. I.e. 128 note polyphony applies to the simultaneous voice use from midi notes not the track allocation. But i am still learning about the FA. Maybe its a bit different.

I think somebody here suggested making some kind of null tone that does not use resources. For tracks that drive external midi equipment.

← Back to FA-06 / FA-07 / FA-08