Hanging notes from integra

It might actually be logic that is the problem. I've suffered with hanging notes and logic for years now and if I load projects from version 9 into X than it still happens. Have you tried creating a new project based on a different template in logic? Might fix it. You can also look at the midi commands sent from logic in the preferences.

you will have top pull the integra7 midi routing from the logic midi sumobject and put it in a monitorobject to demerge it from your midi-sum-setup, otherwise you will get a midi loopback causing those hanging notes. Look in the enviroment, click and ports layer.

I have also hanging notes but not always and it is even if i don't use a computer with software. I use a roland a500 pro with the integra or my nord stage ex and both give the issue. What can i do?

MNordex wrote:

I have also hanging notes but not always and it is even if i don't use a computer with software. I use a roland a500 pro with the integra or my nord stage ex and both give the issue. What can i do?

Which of the boards is generating MIDI Clock?

I have no idea... How can i figure that out?

MNordex wrote:

I have no idea... How can i figure that out?

First of all the Integra should be configured as a slave to receive clock from the nord or from the PCR.

To make MIDI settings on the integra-7 go to: MENU, SYSTEM, navigate to SYNC/TEMPO Tab
Sync Mode= SLAVE
Clock Source= MIDI
System Tempo= ?=MIDI (this is controlled by the Sync Mode)
Tempo Assign Source= SYSTEM or STUDIO SET depending on what you want

The following is just an example of what you could do...

note:Refer to pages 68-81 of the PCR manual
- The PCR could be your MASTER Clock source (SY00=ON)
- Set PCR's Clock Default Tempo to 120 (SY01=120)
- set Clock Port Set to PORT1 (SY02=PORT1)
- set the MIDI I/F switch to OFF (SY08=OFF)
- set MIDI MERGE Destination to MIDI (SY09=MIDI). This will allow for the NORD to be connected to the PCR's MIDI IN and you can actually merge their MIDI signals. Doing this you can use the NORD to control one part (1 channel) of the Integra-7 and the PCR to control two more (if in Split or Layer mode).

Regarding the Nord it must be in the system config or something like that. Set it to not generate clock to the MIDI OUT.

Hope this helps

I've tried it with the nord stage but that doesn't change a thing. I still have hanging notes...

When does the hanging notes happen?
are you just playing the same voice and get hanging notes after a while ?

or are you changing the midi output from the from the controller to change voice on the
Intergra 7 while playing?

If I play notes and change the midi channel on the nord stage notes are Always hanging. When I record a midi track in Cubase and use my sustain pedal notes are hanging, but nog always.

In my Integra i've put the RX channels (except rx programm) to 'off' (menu=> system => midi). Now the Roland A500 pro doesn't have the problems anymore. The notes are getting 'off' by changing a midi channel and I can play with sustain pedal without hearing hanging notes.

As far as I can test right now, I've only got the problem with my Nord stage ex.

I suspected that that was the case.... that used to happen to me.

I don`t know what fixed it....Mite be when I change from my Novation Impulse to MOFX
but I don`t have that problem anymore.....or it just have not happen yet?:)

I am not an MIDI guru. maybe someone is hiding in woodwork than can shine an light to the subject? :)

I guess (for now) the problem is solved!
I've 'played' with the Integra buttons, switched several things to see if it make sense and for now it makes sense and I hope the problem is solved.

I've also made a Cubase record without hanging notes and played on my Nord stage ex without hanging notes when I use my sustain pedal.

Nord stage ex => midi out, Roland Integra 7 =: midi in
Nord stage ex => shift+midi => midi panel A channel 1-16 (switch)
Roland Integra 7: Menu=>System=>Sync/Tempo: Slave
Roland Integra 7: Menu=>System=>Midi=>the last five RX programms 'off' instead of 'on' (by using Cubase: USB Midi Thru: 'on'

HI

I found this thread of deep interest. I encountered the same issue. I connected my I7 to my Computer and added it as an instrument track in Pro Tools 2020.5 played a few notes on the ADVANCE 61 Controller and like clock work the i& stalls after approximately 5 notes.

I made the proposed changes where I changed the Sync on i7 to "SLAVE" and disabled the last 5 RX's setting in System Midi Tab. Seems that corrected the problem. But my curiosity drove me to determine root cause given that this was inconclusive in your report.

I then enabled the last 5 RX and the unit still worked expected even after power of and power of the i7 Post changes.

I will continue my search for a confirmed root cause. This stuff should be on Rolands Support site. I will admit that the unit while slick is not very flexible our robust given the hefty price tag. had to buy a 3rd Party Plug in to use it with Pro Tools in an AAX environment all the while Roland boasting about the new editor for the iMAC.

Anyway.... I'm off the soapbox LOL. Appreciate the share out