JUPITER-80

Jupiter-80 Organ, optimizing it.

Re: Jupiter-80 Organ, optimizing it.

23 Jan 2013, 16:12
Tom_1970 wrote:
Made this comment on their facebook page...
...maybe it will help. ;)
Good initiative! Roland representatives have been known to reply to Facebook comments. :)

To others interested in this: Comment or like on Facebook if you have an account.

Re: Jupiter-80 Organ, optimizing it.

10 Feb 2013, 17:25
Hello,

I'm new to the forum and just wanted to say hello. My company manufactures a MIDI drawbar controller than was originally designed for Nord keyboards, but recently I've been adding support for instruments that use non-standard control schemes, including the Korg Kronos which also uses SYSEX for drawbar control.

I would love to add Jupiter 80 to the list of supported instruments, but I have not been able to find documentation on the specific SYSEX message Roland uses for drawbar control.

If somebody can hook me up with this, I'll be happy to add Jupiter 80 support to the DB-1.

Best Regards,

Dave
http://www.oceanbeachdigital.com

Image

Re: Jupiter-80 Organ, optimizing it.

10 Feb 2013, 17:46
Thanks AnotherScott,

Yes, I was just looking at that thread and the information there is not quite complete. kernell32's post comes close but there's still some ambiguity. I'll send him info seeking clarification. There was also a TB MIDI control thread elsewhere, but that didn't have enough information to crack the code either.

Cheers,

Dave

Re: Jupiter-80 Organ, optimizing it.

10 Feb 2013, 17:49
interesting. W cannot at all assume the addresses are the same for the Integra as the JP80 since there definitely architectural differences between the two. But looking at the JP80 sysex its clear that there are many "reserved" addresses, any of which could be the drawbars.

Someone could also do a test where they do a sysex dump, then change one drawbar and do a sysex dump again, which we could then diff to find the needed address for each drawbar. I'm not setup here to do that at the moment, but if anyone has been doing sysex dumps with their JP-80 they could do this easily and figure it out.

Re: Jupiter-80 Organ, optimizing it.

10 Feb 2013, 18:09
Yes, that's kinda how it went with the Kronos. I don't have handy access to one of those either, but somebody on one of the forums was able to assign Kronos faders to drawbar control, then used MIDI-OX to see what was sent and then played it back to the Kronos to see how it responded. The Korg Sysex documentation was pretty complete and we were able to use it to fill in most of the blanks. The Sysex information in the Jupiter 80 MIDI Implementation manual looks more limited.

The header portion of the Sysex message looks like it will be different for Jupiter 80, 50, and Integra. It's possible the rest of the message shares common elements.

Re: Jupiter-80 Organ, optimizing it.

10 Feb 2013, 23:35
Just jumping in here I was just speaking to a tech at Roland re allocating the rotary on off and speed button to a pedal He seemed to think it would have to go through the MFX and allocate a cc number to it I havnt tried it but this whole thing is a bit disconcerting as the Kurzweil I have does it as its already default setting. So he assured me the designers at Roland love organs but I am begining to wonder if they just like the sound and havnt actually played one!

I also asked about a librarian and he thought that a generic one would work.

Also he said the usb stick is setup like it is for safety in backups.

Re: Jupiter-80 Organ, optimizing it.

10 Feb 2013, 23:52
yes a generic librarian will work but someone somewhere has to go through the painstaking effort to enter all the JP-80 specific sysex info from the manual to setup a config for it, with midiquest or some others.

kind of lame answers, but the simple truth is they have been laying off people at Roland and they don't have resources to take on some of this stuff.

Re: Jupiter-80 Organ, optimizing it.

11 Feb 2013, 00:22
OBDave wrote:
Yes, that's kinda how it went with the Kronos. I don't have handy access to one of those either, but somebody on one of the forums was able to assign Kronos faders to drawbar control, then used MIDI-OX to see what was sent and then played it back to the Kronos to see how it responded. The Korg Sysex documentation was pretty complete and we were able to use it to fill in most of the blanks. The Sysex information in the Jupiter 80 MIDI Implementation manual looks more limited.

The header portion of the Sysex message looks like it will be different for Jupiter 80, 50, and Integra. It's possible the rest of the message shares common elements.
Hi OBDave,
Welcome to the Clan!!

Here are the SysEx messages for the Integra-7 TW Organ Drawbars, and below the adapted ones for the JUPITER-80

Integra-7 (Tested on a Cakewalk A-800 PRO MIDI Controller):
dw1 F0 41 10 00 00 64 12 SS 19 02 00 22 DT S1 F7
dw2 F0 41 10 00 00 64 12 SS 19 02 00 23 DT S1 F7
dw3 F0 41 10 00 00 64 12 SS 19 02 00 24 DT S1 F7
dw4 F0 41 10 00 00 64 12 SS 19 02 00 25 DT S1 F7
dw5 F0 41 10 00 00 64 12 SS 19 02 00 26 DT S1 F7
dw6 F0 41 10 00 00 64 12 SS 19 02 00 27 DT S1 F7
dw7 F0 41 10 00 00 64 12 SS 19 02 00 28 DT S1 F7
dw8 F0 41 10 00 00 64 12 SS 19 02 00 29 DT S1 F7
dw9 F0 41 10 00 00 64 12 SS 19 02 00 2A DT S1 F7

Date type DT0 7bit min 8 max 0

NOTE: This SysEx messages are valid only if TW Organ is selected in Part 1

********************************************************************

JUPITER-80 (I hope it works...):

dw1 F0 41 10 00 00 55 12 SS 19 02 00 22 DT S1 F7
dw2 F0 41 10 00 00 55 12 SS 19 02 00 23 DT S1 F7
dw3 F0 41 10 00 00 55 12 SS 19 02 00 24 DT S1 F7
dw4 F0 41 10 00 00 55 12 SS 19 02 00 25 DT S1 F7
dw5 F0 41 10 00 00 55 12 SS 19 02 00 26 DT S1 F7
dw6 F0 41 10 00 00 55 12 SS 19 02 00 27 DT S1 F7
dw7 F0 41 10 00 00 55 12 SS 19 02 00 28 DT S1 F7
dw8 F0 41 10 00 00 55 12 SS 19 02 00 29 DT S1 F7
dw9 F0 41 10 00 00 55 12 SS 19 02 00 2A DT S1 F7

Date type DT0 7bit min 8 max 0

NOTE: This SysEx messages are valid only if TW Organ is selected in the Upper or Lower Parts


Nice Drawbar Controller BTW!!!
I hope you manage to get it to work with the JP-80 ;-)
Cheers,
Paulo
Make Music and be Happy !!
PauloF

Re: Jupiter-80 Organ, optimizing it.

11 Feb 2013, 03:30
OBDave wrote:
I would love to add Jupiter 80 to the list of supported instruments, but I have not been able to find documentation on the specific SYSEX message Roland uses for drawbar control.

If somebody can hook me up with this, I'll be happy to add Jupiter 80 support to the DB-1.
Hi there! Great project!

If you open the organ file in TB MIDI Stuff (attached in that thread), and edit the controls, you will see all the SysEx commands you need:

Drawbars 1 to 9:
F0411000005512CS10004001xxCEF7
...
F0411000005512CS10004009xxCEF7

Percussion:
F0411000005512CS1000400AxxCEF7

Volume:
F0411000005512CS10004015xxCEF7

Decay:
F0411000005512CS1000400CxxCEF7

Harmonic:
F0411000005512CS1000400BxxCEF7

So, basically, the TW organ uses the parameters for Live Set Tone Modify (Layer 1).

Here "xx" is the value, and everything between "CS" and "CE" (checksum start and checksum end) must be used for the checksum calculation. Remove the "CS" and the "CE" from the command and replace "CE" with the checksum. :)

The main challenge here is the checksum, which depends on the value. This means the controller will either have to generate the checksum on-the-fly or separate SysEx commands must be stored for each value with precomputed checksums.

Re: Jupiter-80 Organ, optimizing it.

11 Feb 2013, 15:19
Hi everyone, thanks for all the support on this! Has anyone used the TB MIDI STUFF file? Does it work on a Jupiter 80? I downloaded the app and loaded the file, but it appears to be generating the wrong checksum.

For example, if you pull the first drawbar all the way out, TB MIDI generates:
F0 41 10 00 00 55 12 10 00 40 01 08 59 F7, when I think it should be generating
F0 41 10 00 00 55 12 10 00 40 01 08 27 F7

For some reason there's no way to choose a fixed width font on this board, so I'll have to post this as an image to preserve my text formatting. But here's the formula I'm using:

Image

It looks like they're just using the sum of the five bytes. I'm curious whether the Jupiter 80 accepts this.

Thanks,

Dave

Re: Jupiter-80 Organ, optimizing it.

11 Feb 2013, 16:53
OBDave wrote:
Hi everyone, thanks for all the support on this! Has anyone used the TB MIDI STUFF file? Does it work on a Jupiter 80? I downloaded the app and loaded the file, but it appears to be generating the wrong checksum.


I'm using the organ file in TB MIDI Stuff and it is working as intended on my Jupiter-80.

Re: Jupiter-80 Organ, optimizing it.

11 Feb 2013, 18:06
OK, that's good to know. To be honest I don't think the checksum as implemented here adds much value. Maybe they've come to the same conclusion and don't bother looking at it anymore... I sent some Sysex test strings with what I believe to be the correct checksums to somebody who's going to use MIDI-OX to send them to his Jupiter 80 and see if it responds as expected.

Is there anything else about the Jupiter that would be helpful for me to know about? Is there a way to set up and upper and lower organ manuals ?

It was noted that the SYSEX string posted above for Integra-7 only works if the organ is selected in Part 1. Does the Jupiter 80 use banks/parts/tracks/etc that would affect or restrict how Sysex drawbar control works?

Re: Jupiter-80 Organ, optimizing it.

11 Feb 2013, 19:28
OBDave wrote:
OK, that's good to know. To be honest I don't think the checksum as implemented here adds much value. Maybe they've come to the same conclusion and don't bother looking at it anymore... I sent some Sysex test strings with what I believe to be the correct checksums to somebody who's going to use MIDI-OX to send them to his Jupiter 80 and see if it responds as expected.

Is there anything else about the Jupiter that would be helpful for me to know about? Is there a way to set up and upper and lower organ manuals ?

It was noted that the SYSEX string posted above for Integra-7 only works if the organ is selected in Part 1. Does the Jupiter 80 use banks/parts/tracks/etc that would affect or restrict how Sysex drawbar control works?
I believe that in JP-80 the TW Organ works in both UPPER and LOWER "Parts" , but needs to be the only Live Set chosen. maybe a JP-80 owner can corroborate this.
Make Music and be Happy !!
PauloF

Re: Jupiter-80 Organ, optimizing it.

11 Feb 2013, 19:30
OBDave wrote:
Hi everyone, thanks for all the support on this! Has anyone used the TB MIDI STUFF file? Does it work on a Jupiter 80? I downloaded the app and loaded the file, but it appears to be generating the wrong checksum.

For example, if you pull the first drawbar all the way out, TB MIDI generates:
F0 41 10 00 00 55 12 10 00 40 01 08 59 F7, when I think it should be generating
F0 41 10 00 00 55 12 10 00 40 01 08 27 F7

For some reason there's no way to choose a fixed width font on this board, so I'll have to post this as an image to preserve my text formatting. But here's the formula I'm using:

Image

It looks like they're just using the sum of the five bytes. I'm curious whether the Jupiter 80 accepts this.

Thanks,

Dave
Dave,
Have you tried this?

dw1 F0 41 10 00 00 55 12 SS 19 02 00 22 DT S1 F7
dw2 F0 41 10 00 00 55 12 SS 19 02 00 23 DT S1 F7
dw3 F0 41 10 00 00 55 12 SS 19 02 00 24 DT S1 F7
dw4 F0 41 10 00 00 55 12 SS 19 02 00 25 DT S1 F7
dw5 F0 41 10 00 00 55 12 SS 19 02 00 26 DT S1 F7
dw6 F0 41 10 00 00 55 12 SS 19 02 00 27 DT S1 F7
dw7 F0 41 10 00 00 55 12 SS 19 02 00 28 DT S1 F7
dw8 F0 41 10 00 00 55 12 SS 19 02 00 29 DT S1 F7
dw9 F0 41 10 00 00 55 12 SS 19 02 00 2A DT S1 F7

Date type DT0 7bit min 8 max 0

Some remarks:
The format I'm using on the Integra (and from the owners manual JP-80 is similar), after the 55 (JP-80), the command should be 12H (Data Set) and then there is an Automatic Checksum Start position SS and Checksum insertion Location and type S1 (S1 is the most common type used by Roland and others. Use S2 if S1 does not work).

I hope this helps
Last edited by PauloF on 11 Feb 2013, 19:42, edited 1 time in total.
Make Music and be Happy !!
PauloF

← Back to JUPITER-80