Hi Guys,
first go at this so please forgive me if I have not put this in the right category.

I am a singer/acoustic guitarist and I recently bought a Boss BR900cd to make CDs to get new gigs.........and Im having problems.

I am recording Vocals and guitar through the on board mike (occasionally using a Sure unidyne 3) and the intial results are not too bad.

However, when I bounce them to the 2 tracks and mix them down (through the mix down patch and the premix patch) the sound degrades slightly.

When I then write the song to CD there is a further, more significant degradation.

When I play the song from the output of the boss it is OK but not great.

When I play the CD through a different CD player its crap. Very hard and one dimentional.

An additional point is that I dont really understand the EQ settings. Trying to boost the low frquencies does not seem to work nether does reducing the high frquencies.

Finally, the manual is ultra pants. Iv heard that there is a video on the operation of Boss br 900cd but it is not available in the UK.

Any help would be much appreciated.

ta

mikeshead
mikeshead

Re: br900cd

2 Feb 2008, 02:20
You can order the DVD online:

http://www.createspace.com/207839

They ship anywhere in the world.

When bouncing or mastering, the Master fader is your recording level and must be set correctly. A common mistake is to use it as a headphone volume control while monitoring the bounce, resulting in recording levels that are either too high (distorted) or too low. Could that be what you did?

- 64Guitars
http://www.geocities.com/sixtyfourguitars/BossBr/


Re: br900cd

2 Feb 2008, 04:46
Tx for reply and for the link, Iv ordered the DVD !

No i dont think the master control is the problem as I have very careful on getting maximum sound levels on the meter wihout going into overload
mikeshead
A guy from another forum pointed out to make sure the effects button was not lit (whichit was), which effectively meant that I was adding effects everytime I bounced or Mastered, which was why the sound was gradually getting worse.

This problem now solved Id like to ask about the EQ. What to the settings mean and how does this relate to the tone of the sound Im getting.
?
mikeshead

Re: br900cd

5 Feb 2008, 00:18
"A guy from another forum pointed out to make sure the effects button was not lit (whichit was), which effectively meant that I was adding effects everytime I bounced or Mastered, which was why the sound was gradually getting worse."

Actually, the status of the COSM EFFECTS button (Insert Effects) usually doesn't matter when bouncing or mastering because the effects are inserted before the source tracks:

Input-->[Effects]-->[Source Tracks]-->[Mixer]-->[Dest. Tracks]

However, sometimes you want to apply insert effects to a pre-recorded track. To allow for those situations, you can change the insert point so that it comes after the source tracks (see page 87 of the BR-900CD manual):

Input-->[Source Tracks]-->[Effects]-->[Mixer]-->[Dest. Tracks]

Since the source tracks are now being directed through the effects before being re-recorded on the destination v-tracks, they will be heard when the destination v-tracks are later played back.

But, when the insert point is set to NORMAL (the default), the source tracks are not directed through the effects while being re-recorded to the destination v-tracks, so the status of the COSM EFFECTS button makes no difference to the recorded sound.

Loop effects are a different story however. They come after the mixer in the signal path, so they will always be included when bouncing or mastering. Since there's no on/off switch for the loop effects, you have to set the Send Levels for each track, the input, and the rhythm to zero before bouncing if you don't want those effects to be recorded. Be aware that there are separate send levels for the [CHO/DLY] and [REV] loop effects and that the reverb send levels default to 10. So, if you don't reduce the reverb levels to zero before bouncing, the reverb will be applied each time you bounce or master. Also, note that loop effects are not recorded in normal Record Mode. They are only recorded when bouncing or mastering.

"Id like to ask about the EQ. What to the settings mean and how does this relate to the tone of the sound Im getting. "

EQ is basically like the Bass, Middle, and Treble controls on your guitar amp or stereo receiver/amplifier. It boosts or cuts the sound level at certain frequencies. There are several different equalizers in the BR. There's track EQ (page 112), Mastering Tool Kit EQ (page 105), and the 4-band EQ in the Insert Effects (page 96). The parameters for each of these equalizers are adequately described in the manual on the pages I've cited.

- 64Guitars
http://www.geocities.com/sixtyfourguitars/BossBr/


Tx again 64

I am managing to produce some half decent cds now.

Yet another question (or two):
mastering..... Are you supposed to use the mix down, then the pre master before chosing which on the other mastering settings to use ie sequencially.

What intial settings for eq would you use on acoustic guitar and on vocals ? I would like a start point before I begin fiddling around to get the appropriate sound.
mikeshead

Re: br900cd

13 Feb 2008, 18:13
mastering..... Are you supposed to use the mix down, then the pre master before chosing which on the other mastering settings to use ie sequencially.

No, you should probably only use one Mastering Tool Kit preset patch. You don't have to use any if you don't want to. That's what I do. I just mix my tracks down to a stereo pair of v-tracks on my BR-864, then export it to a wave file on my PC and burn it to a CD. The Mastering Tool Kit compresses the dynamic range of your song so that you can create a louder master without getting distortion. Many people like a loud master but there are many good technical reasons to avoid it. See this article:

http://en.wikipedia.org/wiki/Loudness_wars

Personally, I very much prefer a big dynamic range to a loud master with little dynamic range (due to compression) so I skip the Mastering Tool Kit altogether. If I want the song to be louder, I can turn up the volume control on my stereo amplifier.


What intial settings for eq would you use on acoustic guitar and on vocals ?

The insert effect preset patches already have EQ in them. So, I would start by choosing an appropriate insert effect patch. I play electric guitar and can't sing to save my life, so I have no real experience recording acoustic guitar and vocals. However, I often record from the piezo pickup of my Godin xtSA which gives a nice acoustic sound. For this, I select one of the five acoustic guitar preset patches (#81-85 - see the patch list on page 202 of the BR-900CD manual). For vocals, try any of the preset patches in the MIC bank (page 203). Number 24, "Vocal EQ", would probably be a good one to start with. If you can't find a MIC preset patch that you like, then choose the one that comes closest to the sound you're after and start editing its parameters. As I said, you'll find EQ settings in the patch as well as a compressor, de-esser, enhancer, and more. Each of these effects has several parameters that you can change to your liking. Also, you can turn off any effects you don't want in the patch.

By the way, you should read through the message archives of the Yahoo! BossBr group for lots more tips:

http://groups.yahoo.com/group/BossBr/

RolandCLAN is a fine forum but it's always good to read other related forums too in order to learn as much as possible about your BR-900. There's a list of links to many BR-related forums in the Links section of the Yahoo! BossBr group. I read five BR forums daily and often reply to posts. But I'm most active in the BossBr group (I'm the owner/moderator of that group).

- 64Guitars
http://www.geocities.com/sixtyfourguitars/BossBr/

Re: br900cd

15 Feb 2008, 06:56
TX 64

Mastering:

just from a sound point of view, I generally get a better sound when I master the 1st and 2nd patches sequencially (mix down and pre master). If I then go onto a third master I tend to get a very slight improvement in the backing but a significant reduction in the vocal (has a "glasssy" effect). Why do Roland call the patch "pre mix" if it is not a pre mix ?

Without any mastering the track does seem lifeless. I suspect that the higher quality of your tracks give a greater 3D effect which makes compression less critical, Perhaps I will get to that stage one day but for now......

I had origonally been recording the acoustic through the on board mike (but without adjusting the EQ as at this stage I didnt understand how it worked) The result was a thin and hard sound. Recording through the sure mike improved matters significantly, however, I am going to try the on borad Mike with more appropriate EQ this week end. After reading your reply I might also try recording from the pick up through the guitar input. I have avioded this in the past as I read you could only get a decent acoustic guitar sound through a mike.

EQ settings

Again tx for info. I dont think Im confident enough yet to mess around with the patch settings, this is something I will save for the future. The vocal sounds are OK at the moment and are improving as i get more understanding of the EQ settings. reverb and delay.

One question: I currently just mess around with the reverb and delay to get a sound I like but is there a difference between the two ? I currently have more delay on vocals with a small amount of reverb, and the reverse on guitar.

Also the fader settings seem crucial for bouncing and mastering, at the moment I have them as high as possible without distortion (usually so the loudest sound is up to the "0" mark) but I note in the DVD it suggests to go to the 6db mark.

Links

Tx for the links to alternative forums, they are as you say, very useful.

cheers
mikeshead
mikeshead

← Back to Studio Zone